Jump to content

CG125 Brat style project bike


Recommended Posts

As the title suggests, I'm part way through a resto/project on my old CG125. It's been sat in the garage for quite some time after I previously had it made road worthy..however it had since broken again and needed a top end rebuild.


I'll post what I've done so far when I have some extra time, but for the moment here is the starting images.


First, let's get this garage tidy and give you a look at the starting point!!


Cheers


:popcorn:

IMG_20170801_194332.thumb.jpg.ee82835e532f8759776d9609ecf000be.jpg

IMG_20170805_132109.thumb.jpg.baaba67cbf86f0281420ff9a763bb64d.jpg

IMG_20170805_174837.thumb.jpg.f25bf2c154fc6d8fcff632491597b746.jpg

Link to comment
Share on other sites

As the title suggests, I'm part way through a resto/project on my old CG125. It's been sat in the garage for quite some time after I previously had it made road worthy..however it had since broken again and needed a top end rebuild.


I'll post what I've done so far when I have some extra time, but for the moment here is the starting images.


First, let's get this garage tidy and give you a look at the starting point!!


Cheers


:popcorn:

If you need any advice on CGs feel free to PM me , I've re built 8 of them and I'd be more than happy to share anything I have learned.
Link to comment
Share on other sites

Thanks Fastbob, will keep that in mind!!




Here's a few more pictures of the bike, I'd just stripped most of the things off of it and also gave the wheels a clean, although they had Hammerite paint on them but that came off with a bit of elbow grease.


My plan is to paint the wheels a kind of matte military colour, the frame will be satin black and then also the tank will be matte military green too. I'm thinking that I may spray a decal on there, something from the war time era? - that's the kind of look I want to go for.


Thoughts are welcome!

IMG_20170807_200045.thumb.jpg.2eebf2bf3629254df6743d0ca31649c2.jpg

IMG_20170807_200055.thumb.jpg.0a5e3e0899208ab92acbb590f3ecd4d7.jpg

IMG_20170807_202451.thumb.jpg.b4601e80ed380fce9270a0a92fda6633.jpg

Link to comment
Share on other sites

  • 4 weeks later...

Hi all, sorry for not updating this in a while!


Next step was to take the engine and have a look at the previous damage that had been caused..there was an ever so slight surface scratch on the piston (as you can clearly see in the photos..I've zoomed in just to make sure you notice it) :lol:


I think the damage was caused from the exhaust valve dropping in whilst the engine was turning over and then getting bettered and seized in due to the bending of it! The valve was a pain to get out!! I fitted a new piston and also new cylinder head because the damage was too much for the old one - shame really as it was genuine Honda.


Here's a few photos to show this.

IMG_20180120_174653.thumb.jpg.ae615ad7bda2f9747083bea8efbaff42.jpg

IMG_20180120_174719.thumb.jpg.cd75084812a9f3e5df833a2bc1789724.jpg

IMG_20180201_114713.thumb.jpg.0e7aa3c7ffa00fda3489562b5803a96b.jpg

IMG_20180201_114722.thumb.jpg.b59d56e2a0177387e5f8d08dc9b7774f.jpg

IMG_20180201_161133.thumb.jpg.c7d28bd3469fdd5119f580b888cec973.jpg

IMG_20180201_161221.thumb.jpg.dce98d0a4d6ca27bc3baf6c7a9ef9a05.jpg

IMG_20180225_130823.thumb.jpg.84f433cd0fc47f2f84d2b1ce9d89b6fc.jpg

IMG_20180330_133210.thumb.jpg.ce1c4d2fb49650bf3d3328dda9ea59f6.jpg

IMG_20180404_212947.thumb.jpg.77173e55e93bf0d3cfe8ed44fc1cf00b.jpg

Link to comment
Share on other sites

  • 2 months later...

Hi do you know if there is any difference between a 6 volt and a 12 volt cylinder head I'm in need of one and someone is selling a (6volt) head I can't for the life of me know why there would be a difference. My bike which I've just been given after the last owner recked the barrel piston and head somehow is a 1986 CG125 thanks in advance

Link to comment
Share on other sites

Hi do you know if there is any difference between a 6 volt and a 12 volt cylinder head I'm in need of one and someone is selling a (6volt) head I can't for the life of me know why there would be a difference. My bike which I've just been given after the last owner recked the barrel piston and head somehow is a 1986 CG125 thanks in advance

 

No difference, see other thread.

Link to comment
Share on other sites

  • 1 month later...

Sorry for the lack of updates...here's my latest one (which is from earlier this year)..I put the rocker on and then set the clearances with a feeler gauge....




...then it was time to oil it up. :lol:


Once that was sorted, it was just a matter of getting the engine in..which I was pretty eager to do before I moved away as I wanted to see if my "creation" worked correctly. If all was okay, I could then start work on the body and modify that to fit the style I'm aiming for.


I did give the front forks a lick of Hammerite, I know it's not powder coating but I'm on a budget here and if I were to powder coat the forks I'd have then needed to powder coat everything else to match!

IMG_20180404_220800.thumb.jpg.20f88bbbf71a076b59382794f652e3fe.jpg

IMG_20180421_170639.thumb.jpg.d443913fc15ef1a1a083b1bcc8bfa786.jpg

IMG_20180624_202804.thumb.jpg.017d4916a01e60588c34f9e2fbfa6820.jpg

Link to comment
Share on other sites

And here is the video of it running for the first time..apologies for not getting the kick start..it proved a little difficult the first time but after that it was fine.


As you can hear, the tappets are a little loud here, so we took the head back off (before it go too hot!) and adjusted them again. For some reason they had completed unset themselves from my prior adjustments even though I did them pretty damn tight?! :?


https://www.youtube.com/watch?v=eM4BIYhWxnQ&feature=youtu.be

Link to comment
Share on other sites

I've just finished top end rebuild on my cg125 project new barrel piston rings new head with valves. I stripped the gear box crank case and inspected all gears and bearings (all ok) I'm just waiting now for a carb insulator to convert the carb mounting as mine was parallel mounting studs and the new head the studs are at 45 degrees kilter so will update on that when it arrives

Link to comment
Share on other sites

I've just finished top end rebuild on my cg125 project new barrel piston rings new head with valves. I stripped the gear box crank case and inspected all gears and bearings (all ok) I'm just waiting now for a carb insulator to convert the carb mounting as mine was parallel mounting studs and the new head the studs are at 45 degrees kilter so will update on that when it arrives

 

Start your own build thread mate........We like build threads with lots of pictures...... 8-)

Link to comment
Share on other sites

And here is the video of it running for the first time..apologies for not getting the kick start..it proved a little difficult the first time but after that it was fine.


As you can hear, the tappets are a little loud here, so we took the head back off (before it go too hot!) and adjusted them again. For some reason they had completed unset themselves from my prior adjustments even though I did them pretty damn tight?! :?


https://www.youtube.com/watch?v=eM4BIYhWxnQ&feature=youtu.be

 

Two things, don't aim for tight tappets just for the sake of making the engine sound quiet, they're called tappets for a reason . A flappy tappet is a happy tappet.And good luck with that pod filter when the bike is on the road , I have never known an engine more easily upset by air box modification than the CG.

Link to comment
Share on other sites

As mentioned the tappets were quite loud compared to what they should have been, so when we took the head back off we then re-set the valve clearances correctly..this really reduced the sound down although there's still a noticeable faint tapping sound. Over all it sounds much better. Here's a pic and video.


https://youtu.be/mwrQdM6ADLs


Excuse the dirty looking oil on the pic..we only topped it up a little bit and left the other oil in there....that happens to be about 5 years old :roll: Luckily I managed to grab a heavily reduced bargain at Tesco for some Mobil racing motorcycle oil..probably a bit overkill for a CG (given that they can run on olive oil lol) but heck it was only £2 reduced from about £18..couldn't pass on that one!! :cheers:


[mention]fastbob[/mention] I agree on the pod filters...I've got my doubts about them, the original air box isn't the prettiest but it seems to do a very good job, just a shame about the size of it, the pod filter will sometimes make the engine cut..I imagine it's needing more fuel given the huge increase in air it's taking in with it. Raise the needle? Bigger main jet? I will note that it isn't the original carb, we got rid of that one in favour of a single cable one.

IMG_20180630_153323.thumb.jpg.f3f6955f72458858ea56331122059cf4.jpg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Welcome to The Motorbike Forum.

    Sign in or register an account to join in.

×
×
  • Create New...

Important Information

Terms of Use Privacy Policy Guidelines We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Please Sign In or Sign Up