Jump to content

Kawasaki GT750 1986


Guest
 Share

Recommended Posts

Late last year I decided to find another project. I had just about finished my Land Rover and the little Peugeot SpeedFight 2.

The GT came up locally and for the right money.

It has been used as a winter hack and the head gasket was blowing.


http://img.tapatalk.com/d/14/02/09/zu9u9a6y.jpg


It was a bit rough but ultimately pretty solid.

Link to comment
Share on other sites

http://img.tapatalk.com/d/14/02/09/zanetuzu.jpg

http://img.tapatalk.com/d/14/02/09/hena9e4u.jpg


Apologies but I seem to be having trouble with attaching photos on my pc and not being able to upload from Dropbox. I'll be back shortly.

Link to comment
Share on other sites

I had one of these as a field bike when I was a kid. We used to put one on the tank and extend the seat with a bit of wood to accommodate three teenagers :D they were the days !

 

Now that sounds like fun.

Link to comment
Share on other sites

So after removing the main parts


http://img.tapatalk.com/d/14/02/09/y4amuvu7.jpg


Then the head off


http://img.tapatalk.com/d/14/02/09/e6urevyp.jpg


If you zoom in this photo you can see the hole in the gasket between one and two.

Edited by Guest
Link to comment
Share on other sites

Now at this point I was thinking, new gaskets and a swizz over with a cloth and put it back together.

However it seemed that the front left corner of the engine had some damage and would need removing to do a reasonable job.

Also I thought I'd actually like to strip and tidy the old tub up. Maybe even keep something for myself that I have restored.

Plus the new gaskets cost me 120 quid and a Suzuki V-strom, £4000!

Link to comment
Share on other sites

http://img.tapatalk.com/d/14/02/09/nupara7a.jpg

http://img.tapatalk.com/d/14/02/09/2u4yqe3a.jpg


Not the best pictures but you get the idea.

So that's up to date to now. Back at work for another 3 days then more spannerring.

Link to comment
Share on other sites

One part I struggled with was removing the release pin/mechanism for the shaft drive.

When you undo the gaiter clip you have about 4mm visibility to find a 2mm hole whilst reaching around to turn the prop to find the hole in the first place.


http://img.tapatalk.com/d/14/02/09/ty5ujusu.jpg


And the what's left of the rest


http://img.tapatalk.com/d/14/02/09/u8ysaqyv.jpg

Link to comment
Share on other sites

One part I struggled with was removing the release pin/mechanism for the shaft drive.

When you undo the gaiter clip you have about 4mm visibility to find a 2mm hole whilst reaching around to turn the prop to find the hole in the first place.


http://img.tapatalk.com/d/14/02/09/ty5ujusu.jpg


And the what's left of the rest


http://img.tapatalk.com/d/14/02/09/u8ysaqyv.jpg

the gt is known for being a nightmare to release the shaft but once you hae done one or two you get the hang of them

Link to comment
Share on other sites

  • 1 month later...

In between work and life I got a few hours in on the GT.

I had to clean all the old gasket from the mating surfaces which seemed to take ages but it's done.

I put the base gasket on, then the fun started. I had already preempted that I'd need 2 ring compressors so they were duly added to the tools collection.

After faffing for ages I was ready for the head, which went on quite well until the pistons started dropping with the head!

I made a tool to help.

http://img.tapatalk.com/d/14/03/16/hy5yvemu.jpg

Although the tool is actually holding the cam chain you can get the idea. Apologies but I didn't get any photos of the early part of the build as I was on my own and hands greasy from oil etc and didn't want to cover my phone in it.

Anyway, the wooden slotty thing works well and slides neatly under the piston either side of the con rod.

Oh and I made 2 of them. Metal ones would have been better but rebuilding bike engines isn't an everyday thing.

Link to comment
Share on other sites

Once back to this stage and the head nuts torqued down I had to read up on the timing chain and cam shafts settings.

I read and re read that page about 20 times and still got it wrong! I set the pistons to tdc but on the wrong two. After altering that I then managed to put the 2 cam shafts in back to front.

http://img.tapatalk.com/d/14/03/16/gesunuje.jpg


Apparently the raised wider ring on the rear left of the back cam is for the electronic tachometer and should be at the exhaust side.

So apart it came again but it was very straightforward after that.


http://img.tapatalk.com/d/14/03/16/je2aqa6u.jpg


Oh and I knocked up the little table too just so I could sit down on the job.

Link to comment
Share on other sites

I can understand taking the time an effort to restore something like a 1980s GS1000 but a GT750? I had one and they're a capable bike but it would be hard to find a bike more boring.

Link to comment
Share on other sites

I can understand taking the time an effort to restore something like a 1980s GS1000 but a GT750? I had one and they're a capable bike but it would be hard to find a bike more boring.

 

Each to there own, if you have no interest then don't read about it?


I had the opportunity to buy the bike at a good price and it was the first bike I had experience with as a learner many years ago.

I have restored a few things in the past, mainly land rovers but bikes are much quicker and take up less space.

My choice.

Link to comment
Share on other sites

I love restoration threads, especially bikes which do not necessarily attract much attention. :D


It is a beautiful machine.

 

Thanks, glad you are enjoying it.

Link to comment
Share on other sites

  • 8 months later...
  • 6 months later...

well this thread does start off saying that the bike came up locally and for the right money


it's about having something to tinker with, my bikes aren't worth very much but i like them,


of course this makes restoration technically uneconomic which my restoration definitely is :(

Link to comment
Share on other sites

  • 4 weeks later...

How are you getting on Twiggy?


Currently helping with a project on a 1982 GT750 with the gf's dad. Its irst time building/restoring a bike and loving it so far.


Would be great to see it when complete.

Link to comment
Share on other sites

  • 2 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Welcome to The Motorbike Forum.

    Sign in or register an account to join in.

×
×
  • Create New...

Important Information

Terms of Use Privacy Policy Guidelines We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Please Sign In or Sign Up